AllExam Dumps

DUMPS, FREE DUMPS, VCP5 DUMPS| VMWARE DUMPS, VCP DUMPS, VCP4 DUMPS, VCAP DUMPS, VCDX DUMPS, CISCO DUMPS, CCNA, CCNA DUMPS, CCNP DUMPS, CCIE DUMPS, ITIL, EXIN DUMPS,


READ Free Dumps For Cisco- 300-135





Question ID 13454

Scenario:
A customer network engineer has edited their OSPF network configuration and now your
customer is experiencing network issues. They have contacted you to resolve the issues
and return the network to full functionality.

Connectivity from R3 to R4, R5 and R6 has been lost. How should connectivity be
reestablished?

Option A

Configure R4 with a virtual link to 192.168.13.2

Option B

Change the R3 and R4 hello-interval and retransmit-interface timers to zero so the link won't go down.

Option C

Add an OSPF network statement for 4.4.4.4 0.0.0.0 area 1 in R3

Option D

Add an OSPF network statement for 192.168.34.3 0.0.0.255 area 2 in R3

Option E

Add an OSPF network statement for 192.168.34.0 0.0.0.255 area 1 in R3

Option F

Answer : E

Explanation: Based on the network diagram, we know that a virtual link will need to be configured to logically connect area 2 to the back area 0. However, this is not the problem as we can see that R3 has been correctly configured to do this. It is, however, missing the network statement for the link to R4. Here, we see that the link to R4 is using the 192.168.34.0 network, but that this network has not been added to OSPF

8] Based on the network diagram, this link should be added to Area 1, not Area 2. Topic 6, Ticket 1: Switch Port Trunk Topology Overview (Actual Troubleshooting lab design is for below network design) ✑ Client Should have IP 10.2.1.3 ✑ EIGRP 100 is running between switch DSW1 & DSW2 ✑ OSPF (Process ID 1) is running between R1, R2, R3, R4 ✑ Network of OSPF is redistributed in EIGRP ✑ BGP 65001 is configured on R1 with Webserver cloud AS 65002 ✑ HSRP is running between DSW1 & DSW2 Switches The company has created the test bed shown in the layer 2 and layer 3 topology exhibits. This network consists of four routers, two layer 3 switches and two layer 2 switches. In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process number 1. DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where necessary. R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002 in the ISPs network. Because the companys address space is in the private range. R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and outside (209.65.0.0/24) network. ASW1 and ASW2 are layer 2 switches. NTP is enabled on all devices with 209.65.200.226 serving as the master clock source. The client workstations receive their IP address and default gateway via R4s DHCP server. The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running on DSW1 and D

Correct Answer E
Explanation


Question ID 13455

The implementations group has been using the test bed to do a proof-of-concept
that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241.
After several changes to the network addressing, routing scheme, DHCP services,
NTP services, and FHRP services, a trouble ticket has been opened indicating that
Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the
following questions.
The fault condition is related to which technology?

Option A

NTP

Option B

Switch-to-Switch Connectivity

Option C

Access Vlans

Option D

Port Security

Option E

VLAN ACL / Port ACL

Option F

Switch Virtual Interface

Correct Answer B
Explanation Explanation: Since the Clients are getting an APIPA we know that DHCP is not working. However, upon closer examination of the ASW1 configuration we can see that the problem is not with DHCP, but the fact that the trunks on the port channels are only allowing VLANs 1-9, when the clients belong to VLAN 10. VLAN 10 is not traversing the trunk on ASW1, so the problem is with switch to switch connectivity, specifically the trunk configuration on ASW1.

Send email to admin@getfreedumps for new dumps request!!!