READ Free Dumps For Cisco- 300-135
| Question ID 15471 | The implementations group has been using the test bed to do a proof-of-concept
that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241.
After several changes to the network addressing, routing schemes, DHCP services,
NTP services, layer 2 connectivity, FHRP services, and device security, a trouble
ticket has been opened DSW1 will not become the active router for HSRP group 10.
Use the supported commands to isolated the cause of this fault and answer the
following questions.
What is the solution to the fault condition?
|
| Option A | Under the interface vlan 10 configuration enter standby 10 preempt command.
|
| Option B | Under the track 1 object configuration delete the threshold metric up 1 down 2 command and enter the threshold metric up 61 down 62 command.
|
| Option C | Under the track 10 object configuration delete the threshold metric up 61 down 62 command and enter the threshold metric up 1 down 2 command.
|
| Option D | Under the interface vlan 10 configuration delete the standby 10 track1 decrement 60 command and enter the standby 10 track 10 decrement 60 command.
|
| Correct Answer | D |
Explanation Explanation: On DSW1, related to HSRP, under VLAN 10 change the given track 1 command to instead use the track 10 command.
| Question ID 15472 | The implementations group has been using the test bed to do a proof-of-concept
that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241.
After several changes to the network addressing, routing schemes, DHCP services,
NTP services, layer 2 connectivity, FHRP services, and device security, a trouble
ticket has been opened DSW1 will not become the active router for HSRP group 10.
Use the supported commands to isolated the cause of this fault and answer the
following questions.
On which device is the fault condition located?
|
| Option A | R1
|
| Option B | R2
|
| Option C | R3
|
| Option D | R4
|
| Option E | DSW1
|
| Option F | DSW2
|
| Correct Answer | E |
Explanation Explanation: DSW references the wrong track ID number. Topic 18, Ticket 13 : DHCP Issue Topology Overview (Actual Troubleshooting lab design is for below network design) ✑ Client Should have IP 10.2.1.3 ✑ EIGRP 100 is running between switch DSW1 & DSW2 ✑ OSPF (Process ID 1) is running between R1, R2, R3, R4 ✑ Network of OSPF is redistributed in EIGRP ✑ BGP 65001 is configured on R1 with Webserver cloud AS 65002 ✑ HSRP is running between DSW1 & DSW2 Switches The company has created the test bed shown in the layer 2 and layer 3 topology exhibits. This network consists of four routers, two layer 3 switches and two layer 2 switches. In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process number 1. DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where necessary. R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002 in the ISPs network. Because the companys address space is in the private range. R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and outside (209.65.0.0/24) network. ASW1 and ASW2 are layer 2 switches. NTP is enabled on all devices with 209.65.200.226 serving as the master clock source. The client workstations receive their IP address and default gateway via R4s DHCP server. The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running on DSW1 and DSW2. In the IPv6 layer 3 topology R1, R2, and R3 are running OSPFv3 with an OSPF process number 6. DSW1, DSW2 and R4 are running RIPng process name RIP_ZONE. The two IPv6 routing domains, OSPF 6 and RIPng are connected via GRE tunnel running over the underlying IPv4 OSPF domain. Redistrution is enabled where necessary. Recently the implementation group has been using the test bed to do a proof-of-concept on several implementations. This involved changing the configuration on one or more of the devices. You will be presented with a series of t