READ Free Dumps For Cisco- 300-115

Question ID 15729	You have been tasked with configuring multilayer SwitchC, which has a partial configuration and has been attached to RouterC as shown in the topology diagram. You need to configure SwitchC so that Hosts H1 and H2 can successfully ping the server S1. Also SwitchC needs to be able to ping server S1. Due to administrative restrictions and requirements you should not add/delete vlans or create trunk links. Company policies forbid the use of static or default routing. All routes must be learned via EIGRP 65010 routing protocol. You do not have access to RouteC. RouterC is correctly configured. No trunking has been configured on RouterC. Routed interfaces should use the lowest host on a subnet when possible. The following subnets are available to implement this solution: 10.10.10.0/24 190.200.250.32/27 190.200.250.64/27 Hosts H1 and H2 are configured with the correct IP address and default gateway. SwitchC uses Cisco as the enable password. Routing must only be enabled for the specific subnets shown in the diagram. Note: Due to administrative restrictions and requirements you should not add or delete VLANs, changes VLAN port assignments or create trunks. Company policies forbid the use of static or default routing. All routes must be learned via the EIGRP routing protocol.
Option A	Answer : + Use RouterC as a router on a stick and SwitchC as a pure Layer2 switch. Trunking must be established between RouterC and SwitchC. + Only use SwitchC for interVLAN routing without using RouterC, SwitchC should be configured as a Layer 3 switch (which supports ip routing function as a router). No trunking requires. The question clearly states No trunking has been configured on RouterC so RouterC does not contribute to interVLAN routing of hosts H1 & H2 -> SwitchC must be configured as a Layer 3 switch with SVIs for interVLAN routing. We should check the default gateways on H1 & H2. Click on H1 and H2 and type the ipconfig command to get their default gateways. \>ipconfig 190.200.250.33 190.200.250.65 Now we have enough information to configure SwitchC (notice the EIGRP AS in this case is 650) VLAN2 and VLAN3 were created and gi0/10, gi0/11 interfaces were configured as access ports so we dont need to configure them in this sim. SwitchC# configure terminal SwitchC(config)# int gi0/1 SwitchC(config-if)#no switchport -> without using this command, the simulator does not let you assign IP address on Gi0/1 interface. SwitchC(config-if)# ip address 10.10.10.2 255.255.255.0 ->RouterC has used IP 10.10.10.1 so this is the lowest usable IP address. SwitchC(config-if)# no shutdown SwitchC(config-if)# exit SwitchC(config)# int vlan 2 SwitchC(config-if)# ip address 190.200.250.33 255.255.255.224 SwitchC(config-if)# no shutdown SwitchC(config-if)# int vlan 3 SwitchC(config-if)# ip address 190.200.250.65 255.255.255.224 SwitchC(config-if)# no shutdown SwitchC(config-if)#exit MLS will not work without this command) SwitchC(config)# router eigrp 65010 SwitchC(config-router)# network 10.10.10.0 0.0.0.255 SwitchC(config-router)# network 190.200.250.32 0.0.0.31 SwitchC(config-router)# network 190.200.250.64 0.0.0.31 THE ROUTER IS CORRECTLY CONFIGURED, so you will not miss within it in the exam, also dont modify/delete any port just do
Correct Answer	A

Explanation

Question ID 15730	Which portion of AAA looks at what a user has access to?
Option A	authorization
Option B	authentication
Option C	accounting
Option D	auditing
Correct Answer	A

Explanation

Previous-Page 1 2. . . 5 6 7 8 9 10 11. . . 74 75 Next-Page

Send email to admin@getfreedumps for new dumps request!!!